&

華秀塑膠為您提供詳細的Lexan PC 500ECR物性表參數。

想了解更多的與Lexan PC 500ECR相關的物性參數，請點擊 LEXAN™ PC產品列表。

如果您對我們的Lexan PC 500ECR有任何疑問，或者想索取Lexan PC 500ECR 物性表datasheet、物質安全資料證書MSDS、ROHS檢驗報告、SGS報告、REACH環保證明、FDA證明、EU法規證明、UL證書及出廠證明COC/COA報告等，敬請撥打我們的服務熱線 020-82582555，或者點擊聯系我們給我們留言。

GE工程塑膠物性目錄 >> LEXAN™ PC >> 500ECR 物性表

[下載500ECR物性表PDF] Consult 500ECR

Lexan PC 500ECR 物性

10 ％玻璃纖維填充,注射模壓級,非氯化非溴化阻燃UL - 94 V0(2.3mm),它有各種不透明的顏色.

Property

TYPICAL PROPERTIES ⁽¹⁾
MECHANICAL	Value	Unit	Standard
Tensile Stress, yld, Type I, 5 mm/min	580	kgf/cm2	ASTM D 638
Tensile Stress, brk, Type I, 5 mm/min	480	kgf/cm2	ASTM D 638
Tensile Strain, yld, Type I, 5 mm/min	4.7	%	ASTM D 638
Tensile Strain, brk, Type I, 5 mm/min	46	%	ASTM D 638
Tensile Modulus, 5 mm/min	25000	kgf/cm2	ASTM D 638
Flexural Stress, brk, 1.3 mm/min, 50 mm span	950	kgf/cm2	ASTM D 790
Flexural Modulus, 1.3 mm/min, 50 mm span	31800	kgf/cm2	ASTM D 790
Taber Abrasion, CS-17, 1 kg	11	mg/1000cy	SABIC Method
Tensile Stress, yield, 5 mm/min	60	MPa	ISO 527
Tensile Stress, break, 5 mm/min	45	MPa	ISO 527
Tensile Strain, yield, 5 mm/min	5	%	ISO 527
Tensile Strain, break, 5 mm/min	7	%	ISO 527
Tensile Modulus, 1 mm/min	3300	MPa	ISO 527
Flexural Stress, yield, 2 mm/min	95	MPa	ISO 178
Flexural Modulus, 2 mm/min	3400	MPa	ISO 178
Hardness, H358/30	115	MPa	ISO 2039-1
IMPACT	Value	Unit	Standard
Izod Impact, unnotched, 23°C, 6.4mm	NB	cm-kgf/cm	ASTM D 4812
Izod Impact, notched, 23°C	13	cm-kgf/cm	ASTM D 256
Izod Impact, notched, -30°C	10	cm-kgf/cm	ASTM D 256
Instrumented Impact Total Energy, 23°C	622	cm-kgf	ASTM D 3763
Izod Impact, unnotched 80103 +23°C	NB	kJ/m2	ISO 180/1U
Izod Impact, unnotched 80103 -30°C	130	kJ/m2	ISO 180/1U
Izod Impact, notched 80103 +23°C	10	kJ/m2	ISO 180/1A
Izod Impact, notched 80103 -30°C	8	kJ/m2	ISO 180/1A
Izod Impact, unnotched 80104 +23°C	NB	kJ/m2	ISO 180/1U
Izod Impact, unnotched 80104 -30°C	NB	kJ/m2	ISO 180/1U
Charpy 23°C, V-notch Edgew 80103 sp=62mm	10	kJ/m2	ISO 179/1eA
Charpy -30°C, V-notch Edgew 80103 sp=62mm	9	kJ/m2	ISO 179/1eA
Charpy 23°C, Unnotch Edgew 80103 sp=62mm	NB	kJ/m2	ISO 179/1eU
Charpy -30°C, Unnotch Edgew 80103 sp=62mm	NB	kJ/m2	ISO 179/1eU
Charpy 23°C, V-notch Edgew 80104 sp=62mm	9	kJ/m2	ISO 179/1eA
Charpy Impact, notched, 23°C	15	kJ/m2	ISO 179/2C
Charpy 23°C, Unnotch Edgew 80104 sp=62mm	NB	kJ/m2	ISO 179/1eU
Charpy -30°C, Unnotch Edgew 80104 sp=62mm	NB	kJ/m2	ISO 179/1eU
THERMAL	Value	Unit	Standard
Vicat Softening Temp, Rate B/50	154	°C	ASTM D 1525
HDT, 0.45 MPa, 3.2 mm, unannealed	143	°C	ASTM D 648
HDT, 1.82 MPa, 3.2mm, unannealed	136	°C	ASTM D 648
CTE, -40°C to 40°C, flow	4.68E-05	1/°C	ASTM E 831
CTE, -40°C to 40°C, xflow	8.46E-05	1/°C	ASTM E 831
Thermal Conductivity	0.21	W/m-°C	ISO 8302
CTE, -40°C to 40°C, xflow	8.46E-05	1/°C	ISO 11359-2
CTE, 23°C to 80°C, flow	4.E-05	1/°C	ISO 11359-2
Ball Pressure Test, 125°C +/- 2°C	PASSES	-	IEC 60695-10-2
Vicat Softening Temp, Rate B/50	141	°C	ISO 306
Vicat Softening Temp, Rate B/120	143	°C	ISO 306
HDT/Be, 0.45MPa Edgew 120104 sp=100mm	144	°C	ISO 75/Be
HDT/Ae, 1.8 MPa Edgew 120104 sp=100mm	136	°C	ISO 75/Ae
HDT/Af, 1.8 MPa Flatw 80104 sp=64mm	136	°C	ISO 75/Af
HDT/Ae, 1.8 MPa Annealed 120°C, 2hrs	142	°C	ISO 75/Ae
Relative Temp Index, Elec	130	°C	UL 746B
Relative Temp Index, Mech w/impact	130	°C	UL 746B
Relative Temp Index, Mech w/o impact	130	°C	UL 746B
PHYSICAL	Value	Unit	Standard
Specific Gravity	1.27	-	ASTM D 792
Mold Shrinkage, flow, 3.2 mm	0.4 - 0.6	%	SABIC Method
Mold Shrinkage, xflow, 3.2 mm	0.4 - 0.6	%	SABIC Method
Melt Flow Rate, 300°C/1.2 kgf	7.5	g/10 min	ASTM D 1238
Density	1.25	g/cm2	ISO 1183
Water Absorption, (23°C/sat)	0.31	%	ISO 62
Moisture Absorption (23°C / 50% RH)	0.13	%	ISO 62
Melt Volume Rate, MVR at 300°C/1.2 kg	7	cm210 min	ISO 1133
ELECTRICAL	Value	Unit	Standard
Hot Wire Ignition {PLC)	4	PLC Code	UL 746A
High Ampere Arc Ign, surface {PLC}	4	PLC Code	UL 746A
Comparative Tracking Index (UL) {PLC}	3	PLC Code	UL 746A
Volume Resistivity	>1.E+15	Ohm-cm	IEC 60093
Surface Resistivity, ROA	>1.E+15	Ohm	IEC 60093
Dielectric Strength, in oil, 0.8 mm	33	kV/mm	IEC 60243-1
Dielectric Strength, in oil, 1.6 mm	25	kV/mm	IEC 60243-1
Dielectric Strength, in oil, 3.2 mm	16	kV/mm	IEC 60243-1
Relative Permittivity, 50/60 Hz	2.9	-	IEC 60250
Relative Permittivity, 1 MHz	2.8	-	IEC 60250
Dissipation Factor, 50/60 Hz	0.001	-	IEC 60250
Dissipation Factor, 1 MHz	0.01	-	IEC 60250
Comparative Tracking Index	150	V	IEC 60112
FLAME CHARACTERISTICS	Value	Unit	Standard
UL Recognized, 94V-1 Flame Class Rating (3)	1.8	mm	UL 94
UL Recognized, 94V-0 Flame Class Rating (3)	2.3	mm	UL 94
Glow Wire Flammability Index 960°C, passes at	1	mm	IEC 60695-2-12
Glow Wire Ignitability Temperature, 1.0 mm	825	°C	IEC 60695-2-13
Oxygen Index (LOI)	36	%	ISO 4589
UV-light, water exposure/immersion	F2	-	UL 746C

Processing

Parameter
Injection Molding	Value	Unit
Drying Temperature	120	°C
Drying Time	2 - 4	hrs
Maximum Moisture Content	0.02	%
Melt Temperature	290 - 320	°C
Nozzle Temperature	280 - 310	°C
Front - Zone 3 Temperature	290 - 320	°C
Middle - Zone 2 Temperature	280 - 310	°C
Rear - Zone 1 Temperature	270 - 300	°C
Hopper Temperature	60 - 80	°C
Mold Temperature	80 - 120	°C

[下載500ECR物性表PDF] Consult 500ECR

相關產品物性: 503R 500R SP7602 3412R SP7604 3414R 3413R BFL2010 BFL2015 3412ECR 500 503 LF1520A

廣州華秀塑膠有限公司不僅是專業的Lexan PC 500ECR原料供應商，亦注重技術支持及全方位的解決方案，提供從材料鑒定、模具設計、成型加工等系列幫助，亦可為客戶量身定制各特殊性能之Lexan PC 500ECR材料，進而協助客戶提高產品竟爭力。

聯絡我們

地址:廣州市天河區中山大道中439號東圃天銀商貿大廈1720-1723室

電話:020-82582555

傳真:020-82523699

Email: [email protected]

Lexan PC 500ECR報價 >>

常規產品

長纖增強尼龍66 長纖增強PPA
長纖增強尼龍6 長纖增強PP
長纖增強復合材料沖擊改性復合尼龍66
沖擊改性復合尼龍6 高強尼龍
沖擊改性復合尼龍沖擊改性復合材料
改性PP 改性的合金料
高溫改性塑料含氟聚合物
改性POM 改性PBT
改性PC 焊接用復合塑料
高比重復合塑料永久防靜電塑料
永久防靜電ABS 永久防靜電合金
永久防靜電POM 其他導電材料
導電尼龍導電PE,導電PP
高溫導電塑料導電POM
導電PBT 導電PC
其他非PTFE自潤滑塑料非PTFE自潤滑PA
非PTFE自潤滑聚苯醚非PTFE自潤滑PPA
非PTFE自潤滑聚甲醛非PTFE自潤滑聚碳酸酯
其他潤滑塑料潤滑尼龍
潤滑烯烴潤滑PPO(PPE+PS)
耐熱潤滑塑料潤滑POM
潤滑PBT 潤滑彈性體
潤滑PC 擠出PBT
熱傳導復合塑料其他PC
EMI/RFI屏蔽復合塑料預著色非填充樹脂

国产精品视频久久-国产精品视频久久久-国产精品视频久久久久-国产精品视频免费播放-国产精品视频免费看-国产精品视频免费看人鲁

Lexan PC 500ECR

華秀塑膠為您提供詳細的Lexan PC 500ECR物性表參數。

華秀塑膠為您提供詳細的Lexan PC 500ECR物性表參數。